Safesmiths Catalog Field reference · pilot

Sargent & Greenleaf 3006 PivotBolt

  • Maker Sargent & Greenleaf
  • Kind electronic safe lock
  • Also called Model 3006 PivotBolt USB Audit Lock; 3006 USB Audit Lock
  • Status active

Summary

Specifications

relockers

A relock device plate normally attaches to the lock body; where it uses the cover screw, the screw must engage at least 4 threads (longer 8-32 screws may be substituted) with no screw exceeding the tapped hole depth.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

mounting

Storage unit may be any material provided the lock gets an electrical ground; mounting surface sturdy, smooth and flat, with 1/4-20 or M6 screw holes.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

Lock body screws: use only the supplied screws, at least four full threads engaged, torque 30 to 40 in.-lb (33.9 to 45.2 dNm); no lock washers or thread sealant. Keypad base screws no more than 15 in.-lb.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

Reversible, non-handed lock: either face of the case may point at the door, matching the direction the blocking part travels; the cable is routed in the recessed channel of the lock cover with a 90 degree bend toward the spindle hole.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

battery type

Two 9 V batteries in the keypad base; the clip will not latch if a battery is inserted backward; the chrome ring lifts for battery access.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

bolt dimensions

Bolt free movement up to 0.352 in. (8.95 mm), of which 0.109 in. sits outside the lock case edge; keep a gap of 0.150 in. (3.8 mm) minimum from the case end to the bolt-blocking part.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

install test

Function test: make sure the boltwork does not bind on the lock bolt in the fully locked position; relieve a bind by removing a little material from the blocking bar opening. Run three or more open-door trials before the door is shut.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

specifications

Install sheet for the Model 3006 PivotBolt USB Audit Lock (S&G Audit Lock 2.0 family); documents 630-889 (3006, revised 9/25/15) and 630-890 (3007).

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

Bolt end pressure: designed to withstand at least 225 lb. (1000 N); boltwork or cam designs must never put more than 225 lb. (1000 N) of side pressure on the bolt.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

Printed 'lock is designed to move' load: 0.0 lb. (0 N).

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

spindle diameter

Spindle (cable) hole at least 0.312 in. (7.9 mm) and at most 0.406 in. (10.3 mm), free of burrs.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

supplied parts

Parts list: base, two 9 V cells, keypad unit, PivotBolt lock body, chrome trim ring, fasteners and a cable.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

notes

Following the sheet is a condition of the warranty and of EN 1300 compliance. The container has to shield the lock body from physical attack and keep security-relevant parts out of reach with the door open.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

Codes: avoid personal data (birth date, street number, phone number) and easily guessed codes; replace the factory default with an individual code before service.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015

The sheet carries a Confidential notice: proprietary to Sargent & Greenleaf, with publication or duplication prohibited.

Sargent and Greenleaf Model 3006 PivotBolt USB Audit Lock Installation Instructions, Document 630-889, revised 9-25-15 · Sargent & Greenleaf, Inc. · 2015